UNDERSTANDING PLUMBING BASICS FOR BATHTUB INSTALLATION

Understanding Plumbing Basics for Bathtub Installation

Understanding Plumbing Basics for Bathtub Installation

Blog Article

Book Appointment Now

Almost everyone is bound to have their personal perception with regards to How to Install a Bathtub.


Installing A Bathtub
Mounting a tub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a new one is likewise a moderately challenging task. If the old bathtub is readily accessible, the project can move easily; if you need to open up a wall to eliminate the old bathtub and position the new bath tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the task as well as fit attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This write-up will aid you install a new tub in your bathroom if you have already bought a new tub as well as do not require to transform the setup of your previous water system pipes.
Your tools as well as material list must comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installation


    To start with, the supporting framework provided with the bath should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap includes a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets system to stop strain on the tub.
    Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use all of the provided washers.
    Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final position.

    Removing Old Touches


    If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be quite problematic because of the limited access that is commonly the case.
    Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
    Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.

    Mounting the Bathtub


    Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four small points.
    The following goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub till the spirit level reviews degree.
    To mount taps, fit the bottom of the outermost flexible tap connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
    Activate the water as well as check all joints as well as brand-new pipework for leakages and tighten them if essential. Fill the tub as well as additionally check the overflow electrical outlet as well as the typical outlet for leakages.
    Lastly, deal with the bath paneling as explained in the supplier's user's manual. Tiling as well as sealing around the tub must wait until the bathtub has actually been utilized at least once as this will certainly resolve it right into its last placement.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipelines.
    If you require to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, place the faucet in the mounting opening in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Protect the tap in position with the manufacturer offered backnut. Once the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bathtub


    In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, causing issues with moisture and possible leakages to the ceiling below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in use. The sealant can split relatively early if you do not consider this movement prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Installing A Bathtub

    I stumbled upon that review on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the internet. For those who enjoyed our article plz do not forget to share it. We enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Call Today

    Report this page